Z

A

P

P

E

R
Z

A


P

P

E

R
This page created with Cool Page.  Click to get your own FREE copy of Cool Page!
Visitor #
Z

A

P

P

E

R
You can check out my Zapper webpage here.
This page was updated on 6/10/01
Welcome to my Dr. Hulda Clark Zapper free circuit schematic homepage!  Dr. Clark's books are "The Cure For All Diseases", "The Cure For All Cancers", "The Cure For HIV/AIDS" and "The Cure For All Advanced Cancers".  This page is for those people out there with electronics project-building experience who wish to build their own Zapper.
Using a 9VDC adaptor with both a (non-CMOS) LM556 timer chip and a CMOS NTE955M timer chip (equivalent to an NE555), the output current of the Simple Zapper was around 7mA to 8mA and the output current of the Enhanced Zapper was around 9mA to 10mA.  When using a DC adaptor, a power supply filter capacitor is not really needed as the circuit is stabilized by the capacitor from pin 5 to ground.

Using a 9V battery, the output current of the Simple Zapper was around 4mA and the output current of the Enhanced Zapper was around 4.5mA.

Mas1911@aol.com
The circuit schematic to the left is a modified version of Dr. Hulda Clark's Zapper.  I changed the configuration of the LED and its current-limiting resistor (along with the value of the resistor) so that when the user touches the probes together, the LED shuts off, thereby verifying that the probes are connected correctly and functioning.  To change the output frequency to ~2,200 hz, change both of the 1.5k resistors to 22k resistors.  To change the output frequency to ~15,000 hz, change both of the 1.5k resistors to 3.3k resistors.  Note the diode which protects the CMOS 555 timer chip from damage when and if the battery is replaced incorrectly.
      This circuit contains only the necessary components (one I.C. chip, two resistors, two capacitors and one diode) to produce a >5-volt, approximately 30,000 hz square wave as per Hulda Clark's books.  Change the 2.2k resistor to 27k if you want a ~2,400 hz square wave.  Put a 1M pot in series with the 2.2k resistor, if you want a variable output frequency.  The Simple Zapper that I'm using has a 1 Meg potentiometer instead of the 2.2k resistor in order to vary the output frequency.  With the oscilloscope's frequency analyzer in storage mode, I hold the Zapper probes and put the oscilloscope probes somewhere on my body and then I vary the frequency of the Zapper using the 1 Meg potentiometer.  While using the Zapper at 7.5V, I noticed that the frequencies around 15,000 hz had larger peaks telling me that my body at the time was more conductive and/or less resistive to frequencies in this range at the given voltage.  With this recent test, I held one Zapper probe in each hand (as opposed to both in one hand as in the previous test) and had the oscilloscope probe (an RCA to 1/4" phone plug adaptor) in my mouth with my lips around the RCA ground.  Change the 2.2k resistor to 4.3k if you want a ~15,000 hz frequency.  Don't forget to solder the ground pin of the chip!

Touch the probes to your tongue as you would do with a 9-volt battery to test whether or not the circuit is working.

      By the way, I've been zapping since the third week of September, 2000, and I can safely say that zapping has changed my life for the better.  Doing the "Epsom salt/grapefruit+olive oil"-liver cleanse from Hulda Clark's book twice recently (the end of the week of 4/15/01) resulted in the expulsion of thirteen large gallstones (3/4" in length, 1/2" in diameter) from my liver as well as smaller gallstones and the cholesterol "chaff".  Pretty gross, huh?

Dr. Hulda Clark's books are available at bookstores and libraries.  In my opinion, her books are worth their weight in gold.